Joined in 2023 
82 
63 About this deal
If you find this content useful, consider Subscribing to my Youtube Channel: http://goo.gl/DDfVab and Social Media. This gives me more negotiation with sponsors which allows me to create more content. UtiliShelf® works for every industry that demands workers be sent out into the field. From electric metering to oil rigs – and beyond – here are some of the ways our customers are using UtiliShelf® : I wanted the holes tight enough that the bolts would actually thread into the boards so I used a 9/64″ drill bit which is smaller than 4mm. 9/64″ = 3.571mm. This just gives a tighter, more solid build and eliminates the chance of the bolt heads pulling through the board. If you drill a big sloppy hole and countersink too deep, it can happen. I personally have never drilled too deep in a big sloppy hole. Countersink/Drill Bit Combo for M4 Bolt heads Countersink Bit for M4 Bolt holes Portable Computer Workstation: No, there isn’t an app for that. Sometimes you just need a computer in the field. And UtiliShelf® provides a great, productive space for it.
The OmniShelf Portable Workstation, Toolbox, Laptop Stand
The MagBench Utility Workstation can be installed on any steel surface in seconds with just two simple steps; place the MagBench Workstation against the steel surface and fold down the front panel. It’s that easyIn addition to the large rear magnets, there are 4 small rare earth magnets on the inside of The Omnishelf at the top, when shelf is opened, to hold tools, phones etc. There is also a File folder space in for storing important paperwork, comes with a large mouse pad doubles as a smooth desk top, Shelf can be used as portable computer workstation. The Mainstay Cutting Board has a recessed top and flat bottom. You can chose to face either side up and I have done both. After using both I preferred the recessed side up to better hold material including hardware, pens , flashlights etc. Service Manual Holder Along with writing you can also hold service manuals weighing up to 15 pounds. Setup the station, open your service manual and you’ll be productive in moments. And you can set it up right where you’re working. As long as there’s a vertical metal surface that is 16 gauge or heavier. On the original magnetic laptop shelf I used two Mainstays 11” x 14.5” Poly Cutting Boards, a 12” piano hinge, Glow in the Dark Paracord and scavenged Hard Drive Magnets.
Utilishelf Plus 1706 Temporary Workstation - Jointing Tech
This DIY Portable Magnetic Laptop Shelf (Laptop Work Station) was designed to be light and compact for easy transport for field use in the elevator industry (IUEC).
Recommendations
Mainstay Poly Cutting Board 11″ x 14.5″ (Dexas NSF Polysafe is the same board): https://amzn.to/3bbfMm3
DIY Compact Portable Magnetic Laptop Shelf Build Instructions DIY Compact Portable Magnetic Laptop Shelf Build Instructions
Cable Storage Bag added to shelf Oh snap, Fabian got the UPGRADE! We added a Velcro Cable Bag to Fabian’s Standard V2 Laptop Shelf Fabian Bravo gets shelf # 004 Glueing Velcro to Cable Bag And he got a companion shelf for a set. Now drill your marks with a 9/64″ drill bit then use a countersink bit to countersink the hole for the bolt heads, or use a countersink drill bit combo, whichever you have or prefer. I have always had deep admiration for people like my supervisor who didn’t need manuals or prints when in the field. Simple Inexpensive DIY Prototype Portable Magnetic Laptop Computer Shelf (V1R1). Compact Portable Laptop Shelf Version 1 took me nearly 20 years to complete when I found the half started project while cleaning my basement and finally finished it. Version 2 had been in my head for years but took that long to find the proper hinges.I wanted a Countersunk Flat Head fastener so the machine screws would be flush with top of the board. I chose M4 – 0.70 Flat Head Countersunk Machine Screws because it’s a readily available fastener size available in the different lengths I required.
Great Deal 
New Comment